Circuit Switched vs Packet-Switched Networks

Circuit switched networks physically connect two endpoints using a communication channel through the network. This utilises a fixed bandwidth for the session whilst the two endpoints remain connected. Packet switched networks offer the ability to split the communication channel into small packets to be sent across the network using multiple routes offering redundancy and increased performance. This utilises dynamic bandwidth management which can be optimised for each connected party and allows for many more services and connections to be active at the same time using the same bandwidth.

In the cellular network GSM (2G) and UMTS (3G) use circuit switching for voice, circuit switched dialup (CSD) and short messaging service (SMS) traffic and use packet switching for GPRS data traffic. In LTE (4G) the entire network uses packet switching and has no capability for circuit switched network support. As a result, the voice and SMS services must be moved over to a packet switched network when using the LTE (4G) network. In addition to this, CSD is no longer supported and GPRS data must be used instead.

Please see Circuit Switched Dialup (CSD) Migration to LTE Application Note' here.

Voice Overview Many applications in use today utilise voice as part of the service offering. This may be to connect two parties together to communicate such as in an elevator emergency failure system, to implement an automated payment service using a dial keypad or report a fault with a system using normal spoken language. Whatever the reason for using the voice service in a cellular system, there are some differences with the LTE network which are described in more detail below.

On legacy devices supporting GSM (2G) and UMTS (3G) services, the voice and SMS components of the system use circuit switching as the transmission channel. For GSM the whole system was built on an analogue infrastructure and digital data was added to the system later with the advance of GPRS packet data. The UMTS system is based on the GSM standard and therefore also supports both digital and analogue components. The UMTS framework allows much higher data rates over GSM but is still based on a similar infrastructure.

LTE on the other hand is entirely digital and has no analogue components at all. Therefore, new methods are used to take advantage of the new features offered by the LTE network as analogue voice calling is no longer possible and the packet switched network must be adopted.

VoLTE (Voice over LTE) Overview The LTE network supports voice and many other additional services in the same way as GSM and UMTS, however, as there is no analogue component the voice must be encoded and sent digitally across the network using packets. The 3GPP body have specified the voice service on LTE which is highly optimised and takes advantage of the additional bandwidth and low latency of the LTE network. This service is called Voice over LTE (VoLTE) and uses the digital packet switched network in a much more efficient way than traditional services. This means that VoLTE can support up to 3 times more voice capacity than previous UMTS networks and up to 6 times more capacity than older GSM networks.

The VoLTE service is provided on LTE over the IP Multimedia System (IMS) network service which is a standardized framework for delivering multimedia services over TCP/IP. It has been developed to allow all content rich media from wireless and wireline applications and allows for advanced services to be provided over the existing infrastructure without the need for individual control functions for each service.

The network provider must support IMS to be able to offer VoLTE as a service to its customers. The IMS framework must be integrated within the network's core architecture and is fundamental to the operation of the network.

Network Usage with Circuit Switch Fall Back (CSFB) With existing GSM (2G) and UMTS (3G) networks, the core functions are built into the application and can be supported with any hardware platform that supports voice and any SIM card that supports voice. This allows for a very simple implementation and calls can be established without any special configuration to the end equipment.

With newer modems that support LTE (4G) in addition to GSM (2G) and UMTS (3G) the firmware in the modem performs a subtle trick to continue having seamless voice support. When connected to the network for transmitting digital packet data, the unit connects to and uses the LTE network. When attempting to dial a voice number the unit automatically switches to UMTS (3G) or GSM (2G) to establish the call. Once the call is finished it reverts to the LTE network. This technology is called circuit switch fall back and is a short-term solution to allow all network providers to offer voice services on the LTE network whilst they implement their own full IMS solution.

This process is fine whilst there are UMTS (3G) and GSM (2G) networks available to use but the analogue networks are being gradually sunset to be replaced entirely with the LTE network.

With the LTE (4G) network it is necessary to configure the device to allow calls to be made using the LTE only network over the IMS service.

SMS Overview The short messaging service (SMS) can be used to send and receive small text messages which can be used in a variety of ways for applications that use the cellular network. The messaging service can be used to configure settings in remote equipment as well as reporting on the current configuration. In addition, the messaging service can inform users directly of a triggered alarm state or indicate when a certain criterion has been met. As with voice, the existing GSM (2G) and UMTS (3G) core functions are built into the system and can be supported with any hardware platform that supports the SMS messaging service and any SIM card that has SMS functio

LINK:	https://www.siretta.com/2025/03/circuit-switched-vs-packet-switched-ne...
	See more stories from sequoia

More from Sequoia