Hiltron Sustains Momentum in Communications Technology with Latest Advances in LEO Satellite Tracking, Satcom Control and 3D Laser-Based Satellite Antenna Scanning

10/10/2022

Hiltron Communications, a globally active satellite system integrator, manufacturer and distributor, reports continuing the expansion of its range of products and services. The mid September IBC 2022 show in Amsterdam was chosen for the first European promotion of Hiltrons HMAM LEO motorised antenna mount, HSACU4 antenna control unit and 3D laser-based satcom antenna scanning service.

Hiltron HMAM LEO low earth orbit satellite tracker

Low-earth-orbit satellites occupy the sharp edge of communications technology, as evidenced by the strong investment in satellite constellations offering low-latency internet access from practically any location, says Jean-Luc George van Eeckhoutte, Hiltron Sales Manager. Our recently introduced HMAM LEO is a complete system combining the strength, precision, smoothness of operation and internal computing capabilities necessary to monitor low Earth orbit satellites. LEO satellites typically have an orbiting period of 128 minutes or less, making at least 11.25 orbits per day. Precise tracking is essential.

Supported on a high-stability ground pillar, HMAM LEO incorporates the computing resources to track satellites using the NORAD TLE (two-line element) data format which defines satellite locations based on their location and velocity. HMAM LEO is capable of accommodating parabolic antennas up to 2.4 metres diameter and can lock onto the desired satellite within the approximately 10 minute timespan where a low earth orbit satellite is in sight. The mount can be oriented within more than 360 degrees of azimuth and 80 degrees of elevation at the required tracking speed.

Hiltron HSACU4 compact antenna control unit

The Hiltron HSACU4 is a compact antenna control unit for use with flyaway antennas. It is based on the same modular architecture as the HACU antenna control unit which is used for antennas at hundreds of earth stations worldwide. Elements such as a polarisation driver, an integrated beacon receiver or power supply modules for the LNBs can be integrated. Control and monitoring are performed through an Ethernet link with an intuitive web interface, or via a directly connected handheld unit. An auto-pointing function can be activated using the web interface which displays the coordinates of the target satellite. After locating the satellite, the HSACU4 progresses to fine-adjustment mode. It can also scan a predefined area and search within this area for a satellite. Steptrack and TLE for NORAD data are supported and can be automatically activated after fine pointing of the antenna. Prediction tracking is included for inclined-orbit satellites.

Hiltron ESA 3D Laser-Based Satellite Antenna Evaluation

3D laser scanning and evaluation of teleport antennas is service based on technology developed by Hiltron's subsidiary partner, ESA Microwave GmbH. It allows reflectors of practically any size to be measured quickly and at very high resolution as part of a complete performance evaluation. This is especially important when teleport antennas are upgraded to higher frequencies such as the Ka-band.

The 3D laser scanning technique we use is far more accurate than the commonly employed photogrammetry method and can be performed while the antenna is actually in operation, comments Peter Kneissl, Head of Research & Development at ESA Microwave. It is also much more efficient than photogrammetry which requires manual attachment of measurement targets to the reflector, a time-consuming process and one which results in only a few hundred points being measured. Our technique can capture a million surface reference points per second with a geometric accuracy of less than 1 mm. The resultant information is integrated into a cloud of approximately 60 million points from which a computer-aided design model is created. After digitisation and computation of the reflector and sub-reflector topography, we use the ingested data to calculate alignment, registration and any required fine-tuning such as surface restoration. Measured specifications and related performance parameters are delivered to the antenna operator or owner together with recommendations clarifying whether the antenna would benefit from upgrading, conversion or fitting with a multi-band feed system.

The 3D laser-based satellite antenna scanning service is available to new and existing Hiltron customers for any brand and model of satellite reflector, up to 35 metres in diameter..

For further requests, please contact

Jean-Luc George van Eeckhoutte

Sales Manager

jeanluc.george@hiltron.de

Tel: +49 (0) 7191 34357-27

Website: www.hiltron.de

Hiltron Communications, Emil-Rathenau-Str., 71522 Backnang, Germany

Tel: +49 (0)7191 343 570 | Fax: +49 (0)7191 3435 750 |

LINK:	https://www.hiltron.de/News.3957.aspx?recordid3957=1632...
	See more stories from hiltron

Hiltron Sustains Momentum in Communications Technology with Latest Advances in LEO Satellite Tracking, Satcom Control and 3D Laser-Based Satellite Antenna Scanning

More from Hiltron

03/12/2024

09/07/2024

28/06/2024

02/05/2024

06/03/2024

02/02/2024

18/01/2024

14/08/2023

09/08/2023

19/06/2023

06/02/2023

07/12/2022

27/10/2022

10/10/2022

05/09/2022

13/06/2022

17/08/2021

14/07/2021

25/05/2021

25/01/2021

17/12/2020

06/10/2020

12/08/2020

12/08/2020

22/10/2019

12/09/2018

12/09/2018

12/09/2018

15/05/2018

03/04/2018

26/03/2018

10/02/2018

30/01/2018

02/12/2017

26/10/2017

24/08/2017

05/07/2017

20/06/2017

20/06/2017

20/06/2017

20/06/2017

20/06/2017

15/06/2017

15/06/2017

29/03/2017

18/01/2017

17/11/2016

19/10/2016

14/09/2016

12/07/2016